R.L. Drake now offers you superior performance and extensive channel capacity with the VM2551 agile video modulator. Another quality product from Drake, the VM2551 is a vestigial sideband, agile modulator with synthesized visual and aural carriers and a full +55 dBmV output level.
Designed to accept composite NTSC video and audio inputs from a satellite receiver, video server, off-air demodulator, DVD player, VCR, or similar source, the VM2551 features front panel video and audio over-modulation indicators and level controls to permit easy setup of modulation levels.
The use of frequency synthesis provides complete frequency agility in the range of 54 to 550 MHz using off-air or CATV (STD, IRC, or HRC) channel plans. In compliance with FCC regulations, channels that fall in specified aeronautical bands feature automatic frequency offset.
The use of a superior SAW filter in the IF circuitry allows adjacent channel operation when used with other modulators or signal sources. A composite IF loop following the SAW filter and before signal conversion to the final RF output channel allows the insertion of scrambling equipment or an IF switch to provide switchover for EAS operation.
If required, the audio preemphasis may be defeated to allow use with a baseband stereo encoder or the normal internally generated aural carrier can be disabled and an externally sourced 4.5 MHz signal can be applied to the rear panel input.
These features, combined with a carefully designed low distortion output stage, provide reliable and economical performance in an adjacent channel +55 dBmV cable television or private cable environment.
VM2551 Technical Specifications |
|
RF |
|
Frequency Range: |
82 channels, 54-550 MHz CATV channels 2-78 and 95-99. |
Output Level: |
+55 dBmV, (typically adjustable +40 to +55 dBmV) |
Output Impedance: |
75 Ohms, return loss of 12 dB nominal. Type "F" connector. |
AV Ratio: |
Audio carrier -18 to -12 dB referenced to video carrier, adjustable. |
Frequency stability: |
Visual carrier within ±5 kHz on FCC offset channels, ±10 kHz on all channels. |
Intercarrier Frequency: |
4.5 MHz ± 2 kHz. |
FCC Frequency Offsets: |
Automatic (+12.5 kHz or +25 kHz for aeronautical channels) |
In-Channel C/N: |
62 dB typical, 60 dB minimum. |
Spurious Outputs: |
-60 dBc minimum, measured at -15 dB A/V ratio and with modulator output level of +55 dBmV |
Broadband Noise: |
-75 dBc typical, referenced to video carrier. (4 MHz BW @ ±12 MHz or greater offset) |
Video |
|
Input Level for 87.5%: |
1 Vp-p ±3 dB, manual gain adjust with overmodulation indicator. |
Input Impedance: |
75 Ohms, Type "F" connector. |
Frequency Response: |
30 Hz to 4.2 MHz, ±1.5 dB |
Video S/N: |
60 dB, luminance weighted |
Differential Gain: |
±5% (10 to 90% APL) |
Differential Phase: |
±5 degrees (10 to 90% APL) |
L/C Delay: |
Within 50nSec of FCC predistortion. |
Audio |
|
Input level for 25KHz Peak Deviation |
175 mV rms minimum. 250 mV rms nominal. Manual gain adjustment with front panel control and overmodulation indicator. |
Input Impedance: |
10K Ohms, unbalanced. RCA Phono connector. |
Pre-emphasis: |
75 µSec., defeatable |
Frequency Response: |
50Hz to 15kHz, ±1.5 dB, |
Total Harmonic distortion: |
1.5% maximum |
Hum and noise: |
-60 dBm minimum, referenced to 25 kHz peak deviation. |
4.5 MHz Input Level: |
37 dBmV for -15 dB A/V ratio. (Change internal jumper to activate.) Input connector is type "F". |
Composite IF Loop |
|
Loop Level: |
+40 dBmV (visual carrier) |
IF Frequency: |
45.75 MHz visual carrier, 41.25 MHz aural carrier. Loop output is after SAW filtering. |
Loop Input/Output Impedances: |
75 Ohms, Type "F" connectors. |
Isolation: |
Greater than 60 dB |
General |
|
AC Power Input: |
115 VAC, ±10%, 60 Hz, 16 watts |
Operating Temperature Range: |
0° to 50° C, ambient |
Size: |
1.75"H x 19"W x 11.8"D |
Weight: |
9.25 lbs. (4.2 Kg) |
Specifications, price, and availability are subject to change without notice or obligation.
Manufacturer | Drake |
---|