Imagine OP+SFP1+TR13 1310NM WAVELENGTH SFP TRANSCEIVER; Small...
Small form factor pluggable (SFP) for Imagine Communications Broadcast fiber optic products; 1310 nm wavelength transceiver; up to 2.5 Gb/s bandwidth-capable
Manufacturer: Imagine Communications
$500.00
Availability: In stock
SKU
OP+SFP1+TR13
Manufacturer: Imagine Communications
Imagine OP+SFP1+TR13 1310NM WAVELENGTH SFP TRANSCEIVER; Small Form Factor (SFP) for Fiber Optic Products. 1310nm wavelength transceiver. Up to 2.5Gb/s bandwidth capable for Datacom/Telecom or TDM solutions
Small form factor pluggable (SFP) for Imagine Communications Broadcast fiber optic products; 1310 nm wavelength transceiver; up to 2.5 Gb/s bandwidth-capableThe OP+VTX transceiver module enables professional broadcast-quality transport of duplex video, audio and ancillary data over a single fiber optic interface.
Every module contains both transmitter and receiver blocks. Occupying two slots within a 6800+ frame, the OP+VTX supports one autosensing mixed video channel and two analog audio channels. Additionally, the OP+VTX supports one 10/100 Base-T Ethernet and two RS-232/RS422/RS485 serial data communication ports. Available in 1310nm, the OP+VTX module is ideal for any facility — from broadcast and post-production to satellite, cable and telco — that requires the transport of analog composite or SDI video and analog audio signals over fiber optic lines.
Features
- Autosensing support for analog, SD-SDI, or HD-SDI video input
- Support for black-burst or tri-level sync.
- Four analog audio inputs
- Four analog audio outputs
- Dual bidirectional independent RS-232/422/485 (two- or four-wire)
- Support for 10/100 Base-T Ethernet
- SFP transceiver adaptability
- Optical power monitoring and alarm thresholds
- Card-edge, remote and full CCS control and monitoring
Specifications
Specifications and designs are subject to change without notice
FIBER OPTIC INPUTS
| Item | Minimum | Typical | Maximum | Note |
|---|---|---|---|---|
| Number of Inputs | 1 | 1 | ||
| Input Wavelength | 1260 nm | 1620 nm | ||
| Optical Power Monitor Accuracy | -3 dB | 3 dB | ||
| Sensitivity | -20 dBm | -19 dBm | OP+SFP1+TR13 | |
| Overload | -3 dBm | OP+SFP1+TR13 |
FIBER OPTIC OUTPUTS
| Item | Minimum | Typical | Maximum | Note |
|---|---|---|---|---|
| Number of Outputs | 1 | 1 | ||
| Peak Wavelength (FP) | 1300 nm | 1310nm | 1320 nm | OP+SFP1+TR13 |
| Spectrum Width (RMS) (FP) | 2 nm | 4 nm | OP+SFP1+TR13 | |
| Average Output Power | -9.5 dBm | -5 dBm | 0 dBm | OP+SFP1+TR13 |
| Optical Rise/ Fall Time | -200 ps | 270 ps | No filter; 20% to 80% | |
| Extinction Ratio | 7 dB | 9 dB | - | 2.1 GHz filter (fourth order Bessel) |
| Jitter | <0.2 UI pk-to-pk |
| VIDEO INPUT/OUTPUT | |
|---|---|
| SD-SDI (270 M) | |
| Input | |
| Standards | SMPTE 259M-C, 270 Mb/s, 525/625 component |
| Connector | BNC (IEC 169-8) |
| Impedance | 75 ohms |
| Return Loss | >15 dB from 5 to 270 MHz |
| Equalization | <=918 ft (280 m) for Belden 1694A |
| Output | |
| Standards | SMPTE 259M-C, 270 Mb/s, 525/625 component |
| Quantization | 10-bits |
| Connector | BNC (IEC 169-8) |
| Impedance | 75 ohms |
| Return Loss | >15 dB, typical, from 5 to 270 MHz |
| Signal Level | 800 mV ±10% |
| D.C. Offset | 0 V ±0.5 V |
| Rise and Fall Time | 400 to 1500 ps (20% to 80%) |
| Overshoot | <10% of amplitude |
| Jitter | <0.2 UI (pk-pk) |
| HD-SDI VIDEO (1.5G) | |
|---|---|
| Input | |
| Standards | SMPTE274M: 1080i/60,1080i/59.94, 1080i/50, 1080p/30, 1080p/29.97, 1080p/25, 1080p/24, 1080p/23.98, 108psf/23.98, 1080psf/24 SMPTE296M: 720p/60, 720p/59.94, 720p/50 |
| Connector | BNC (IEC169-8) |
| Impedance | 75 ohms |
| Return Loss | >15 dB (typical) from 5 to 1485 MHz |
| Equalization | <=393 ft (120 m) for Belden 1694A |
| Output | |
| Standard | Same as supported input standard |
| Quantization | 10-bits |
| Connector | BNC (IEC 169-8) |
| Impedance | 75 ohms |
| Return Loss | >15 dB, typical, from 5 to 1485 MHz |
| Signal Level | 800 mV ±10% |
| D.C. Offset | 0 V ±0.5 V |
| Rise and Fall Time | <270 ps |
| Overshoot | <10% of amplitude |
| Jitter | Timing jitter: <1UI (673 ps pk-pk)Alignment jitter: <0.2 UI (135 ps pk-pk) |
| Analog Composite Video Input | |
|---|---|
| Number of Inputs | 1 (75 ohms terminated) |
| Connector | BNC (IEC169-8) |
| Standards | NTSC (SMPTE 170M), PAL-B (ITU624-2) |
| Level | 1 V pk-pk; ±6 dB nominal for composite video |
| Impedance | 75 ohms |
| Return Loss | >40 dB to 6 MHz |
| Common Mode Range | 5 V pk-pk, typical |
| Common Mode Rejection Ratio | >60 dB at 60 Hz |
| Digital Video Conversion | |
|---|---|
| Quantization | 12-bit |
| Frequency Response | ±0.1 dB to 6 MHz |
| Signal-to-noise Ratio | >62 dB RMS typical |
| Analog Composite Video Output | |
|---|---|
| Number of Outputs | 1 (75 ohms terminated) |
| Connector | BNC (IEC169-8) |
| Standard | NTSC (SMPTE170M), PAL-B (ITU624-2) |
| Signal Level | 1 V pk-pk nominal for composite video |
| Signal Quantization | 12-bit |
| Impedance | 75 ohms |
| Return Loss | >40 dB to 6 MHz |
| DC Offset | <±50 mV |
| SNR | >54 dB RMS to 6 MHz |
| ANALOG AUDIO | |
|---|---|
| Input | |
| Number of Inputs | 4 mono channels |
| Connector | Weidmuller 24-pin locking header-socket pair |
| Input Audio Level | 28 dBu to 16 dBu, (adjustable in 2 dB increments) |
| Input Impedance | High impedance |
| Output | |
| Number of Outputs | 4 mono channels |
| Connector | Weidmuller 24-pin locking header-socket pair |
| Output Audio Level | 28 dBu to 16 dBu into >10k ohms load (adjustable in 2 dB increments) |
| Output Impedance | 66 ohms |
| ANALOG AUDIO TO ANALOG AUDIO | |
|---|---|
| Analog Audio Path | |
| Number of Channels | 4 mono channels |
| Connector | Weidmuller 24-pin locking header-socket pair |
| Frequency Response | <±0.1 dB @ 0 dBFS (+28dBu), 20 Hz to 20 kHz, typical |
| THD+R | >90 dB @1kHz (-80 to +21dBu) |
| SNR | >100 dB |
| Cross Talk | >80 dB, 20 Hz to 20 kHz, typical |
| Linearity | <±1.0 dB (to -100 dBFS), typical |
| SERIAL PORT | |
|---|---|
| Generic Serial Data | |
| Number of Channels | 2 |
| Standard | EIA/TIA-232 or EIA/TIA -485, selectable |
| Connector | IPL1-105-01-S-D, 2, 3 or 4 pins |
| EIA/TIA-232-E/485 | |
|---|---|
| EIA/TIA-232-E | |
| Number of Channels | Up to 2 channels |
| Standard | EIA/TIA-232-E |
| Connector | IPL1-105-01-S-D, 3-pins |
| Baud Rate | <460 Kb/s |
| Maximum Output Level (unloaded) | <±25 V |
| Output Level (loaded) | ±5 V to ±15 V |
| Driver Load Impedance | 3 to 7 ohms |
| Slew Rate | <30 V/ms |
| Max Driver Current in High-Z | ±6 mA @ ±2 V |
| Receiver Impedance | 3 to 7 ohms |
| Receiver Sensitivity | ±3 V |
| Receiver Input Voltage Range | ±15 V |
| EIA/TIA-485 | |
| Number of Channels | Up to 2 channels |
| Standard | EIA/TIA-485 (EIA/TIA-422 compatible) |
| Connector | IPL1-105-01-S-D, 4-pins |
| Input Termination | 120 ohms, jumper selectable |
| Baud Rate | <460 Kb/s |
| Maximum Output Level (unloaded) | <±6 V |
| Output Level (loaded) | >±1.5 V |
| Driver Load Impedance | 50 ohms (422) or 27 ohms (485) |
| Max Driver Current in High Z | ±100 mA |
| Receiver Impedance | 12 k ohms |
| Receiver Sensitivity | ±200 mV |
| Receiver Input Voltage Range | -7 to 12 V |
| Ethernet Input/Output | |
| Number of Inputs | 1 (balanced pair) |
| Number of Outputs | 1 (balanced pair) |
| Connector | RJ-45 per IEC169-8 |
| Standard | 10/100 Base-T |
| Speeds Supported | 10/100 Mb/s |
| Impedance | 100 ohms |
| Return Loss | 18 dB |
| Cable Equalization | 0 to 328 ft (0 to 100 m), CAT-5 UTP |
| Propagation Delay | |
| HD-SDI | 60 us |
| SD-SDI | 343 us |
| Composite | 28.1 us |
| Analog Audio | 1.9 ms |
| Power consumption | <12 W |
| Start up time | <10 seconds |
| Temperature | 32 to 113 F (0 to 45 C) |
Manufacturer: Imagine Communications
| Manufacturer | Imagine Communications |
|---|
Write Your Own Review
Check items to add to the cart or
My Wish List
Last Added Items
You have no items in your wish list.