The VPL-PHZ10 laser projector is a versatile, affordable choice for installation in a wide range of education, business and entertainment environments.The powerful Z-Phosphor laser light source is teamed with Sony's advanced BrightEra 3LCD projection engine to deliver extremely bright, detail-packed WUXGA resolution images with generous 5000 lumens brightness and rich, stable colours. This laser light source allows up to 20,000 hours of virtually zero maintenance operation without the worry of sudden lamp failures.
NTSC, PAL, SECAM, 480/60p, 576/50i, 720/60p, 720/50p, 1080/60i, 1080/50i The following items are available for HDMI input only; 1080/60p, 1080/50p, 1080/24p
RGB / Y PB PR input connector:Mini D-sub 15 pin (female) Audio input connector: Stereo mini jack
INPUT B
HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support
INPUT C
HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support
INPUT D
HDBaseT interface connector: RJ45, 4 play (Video, Audio, LAN, Control)
VIDEO IN
Video input connector: BNC Audio input connector: Shared with INPUT A
OUTPUT
Audio output connector: Stereo mini jack
REMOTE
D-sub 9-pin (male) / RS232C
LAN
RJ45, 100BASE-TX (Shared with INPUT D)
USB
TYPE-A
USB
TYPE-B
Acoustic Noise*1
Lamp Mode: Standard / Middle / Low
36 dB / 28 dB / 25 dB
Operating temperature / Operating humidity
Operating temperature / Operating humidity
0to 40C (32F to 104F) / 20 % to 80 % (no condensation)
Storage temperature / Storage humidity
Storage temperature / Storage humidity
-10 to +60C (14F to 140F) / 20 % to 80 % (no condensation)
Power requirements
Power requirements
AC 100 V to 240 V, 4.3 A to 1.7 A, 50 Hz / 60 Hz
Power Consumption
AC 100 V to 120 V
Mode: Standard: 424 W
AC 220 V to 240 V
Mode: Standard: 403 W
Power Consumption (Standby Mode)
AC 100 V to 120 V
0.5 W (when "Standby mode" is set to "Low")
AC 220 V to 240 V
0.5 W (when "Standby mode" is set to "Low")
Power Consumption (Networked Standby Mode)
AC 100 V to 120 V
12.5 W (LAN) 13.2 W (optional WLAN module) 16.8 W (HDBaseT) 17.4 W (ALL Terminals and Networks Connected, when "Standby Mode" is set to "Standard")
AC 220 V to 240 V
11.9W (LAN) 12.6W (optional WLAN module) 17.0W (HDBaseT) 17.6W (ALL Terminals and Networks Connected, when "Standby Mode" is set to "Standard")
Standby Mode / Networked Standby Mode Activated
Standby Mode / Networked Standby Mode Activated
Approx. 2 Minutes
Heat dissipation
AC 100 V to 120 V
1446 BTU/h
AC 220 V to 240 V
1374 BTU/h
Dimensions (W x H x D)
Dimensions (W x H x D) (without protrusions)
510 x 113 x 354.6 mm (20 3/32 x 4 7/16 x 13 31/32 inches)
Mass
Mass
Approx. 8.7kg (19 lb)
Supplied accessories
Remote commander
RM-PJ8
Notes
*1
The figures are approximate. They vary depending on the environment or how the projector is used.
*2
The value is in accordance with ISO 21118, and may differ depending on the actual unit. Brightness and contrast vary depending on use conditions and environments.
*3
The value is light output measured at center area of screen in Standard mode, and average of all products shipped.
*4
Available for VESA Reduced Blanking signal.
This projector has a total constant brightness of 4500 lumens for up to 14,000 hours depending on usage environment. This enables users to experience the projectors original level of image quality for years, while achieving a maximum 5,000 lumens brightness when the constant brightness mode is off.